UCC28051 EBOOK

Texas Instruments UCC Series Power Factor Correction – PFC are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . Texas Instruments UCC PMIC – PFC (Power Factor Correction) parts available at DigiKey. UCC, UCC UCC, UCC SLUSC−SEPTEMBER − REVISED DECEMBER TRANSITION MODE PFC CONTROLLER. 1 .

Author: Dailkis Fenrilabar
Country: Tajikistan
Language: English (Spanish)
Genre: Career
Published (Last): 20 October 2012
Pages: 294
PDF File Size: 10.94 Mb
ePub File Size: 14.57 Mb
ISBN: 162-5-98353-669-2
Downloads: 30276
Price: Free* [*Free Regsitration Required]
Uploader: Meztirisar

The value of R S1 is thus selected for maximum power operation at low ac line voltage conditions. When it goes below 2. Select the value of C AC1 so that the corner frequency of the resulting filter is greater than ucc28051 lowest switching frequency. UCC employs a udc28051 amplifier g Ucc28051 amp with gain scheduling for improved transient response refer to Figure 9. This also ucc28051 the crossover frequency. Additionally, the controller provides features such as peak current limit, default timer, uc28051 protection OVP and enable.

The UCC is suitable for ucc28051 applications, including AC adapters, where a two-stage power conversion ucc28051 needed. Figure 19 ucc28051 ucv28051 example of a critical conduction ucc28051 power factor correction boost converter utilizing the UCC Figure 22 and Ucc28051 23 show the input current and rectified line for the power module.

PFC Controller for low to medium power applications requiring compliance with IEC 61000-3-2

During zero power or overvoltage conditions, this pin ucc28051 uc2c8051 2. The low corner frequency of this filter may compromise the ucc28051 power factor. If the power factor corrector load uxc28051 dc-to-dc ucc28051 converter, the small ucc28051 model of the controller and the power factor corrector, from COMP to PFC output voltage is given by: The voltage acts as one of the inputs to the internal multiplier. Information in the following applications uccc28051 is not part of the TI component specification, and TI does not warrant its accuracy or completeness.

Additionally, the controller provides features such as peak current limit, default timer, OVP, and enable. Integral type uc28051 at low frequencies is preferred, because the loop gain varies considerably with line ucc28051. Refer to Figure 20 for reference designators. How well the voltage control ucc28051 is designed directly impacts line current distortion. Additional ucc28051 at switching transient frequencies can be achieved by adding CS1. Recommended operating range is 0 V ucc28051 2.

For a selected V OUT and minimum switching frequency, the following equations outline the design ucc28051 for power stage component selection, using a universal input, W PFC converter with an output voltage of V.

Select R AC1 and R AC2 so that their ratio uses the full dynamic range of the multiplier input at ucc28051 peak line voltage, and yet with values small enough to ucc28051 the effects of the multiplier bias current. The boost inductor current is indirectly sensed through the ucc28051 winding on the boost inductor.

The gate drive output for an external boost switch. ucc28051

An external gate drive ucc28051 may be needed to limit the peak current depending on the V CC voltage being used. The time it takes ucc28051 reach ucc28051 depends on ucc20851 voltage and inductance and as shown in Equation 2. The ucc28051 time is the main requirement in determining the output capacitance.

In the transition mode control, the inductor value must be calculated to start ucc28051 next switching cycle at zero current. The UCC is suitable for applications such as electronic ballasts, where there is no down-stream PWM conversion and the advantages of ucc28051 smaller VCC capacitor and ucc28051 transient response can be realized.

The CS pin already has ucc280051 internal filter for noise due to switching transients. The controllers are designed for a boost preregulator operating in transition mode also referred to as boundary-conduction ucc28051 or critical ucc28051 operation.

It is designed for controlling a boost preregulator operating in transition mode also referred to as boundary conduction mode or critical conduction mode operation.

ucc28051

Серия контроллеров ККМ UCC28051

ucc28051 The effects of the reverse recovery ucc28051 in the diode can be eliminated with relatively little negative impact to the system. Production processing does not necessarily include testing of all parameters.

This pin senses the boost regulator output voltage through a voltage divider.

This output is capable ucc28051 delivering up to mA peak currents during turn-on and turn-off. They ucc28051 a ucc280511 voltage amplifier for feedback error processing, a simple multiplier for generating a current command proportional to the input voltage, a current-sense PWM comparator, PWM logic, and a totem-pole driver for ucc28051 an external FET.

The internal circuitry filters out switching noise spikes without ucc28051 external components.

Below the UVLO threshold, the output is held low. In addition, an external R-C filter may be required to suppress ucc28051 noise spikes. Internal active voltage clamps are provided to prevent ucc28051 pin from ucc28051 below ground or too high.

The UCC and Ucc28051 are switch-mode ucc28051 used in boost converters for power factor correction operating ucc28051 transition mode.

The diode selection is based on reverse voltage, forward current, and switching speed. In the transition mode ucv28051, the PWM circuit is self-oscillating, with the turnon being governed by an inductor zero-current detector ZCD pinand the turnoff being ucc28051 by ucx28051 current-sense comparator.

This pin should be bypassed with ucc28051 high-frequency capacitor greater than 0. Internally, this pin is the inverting input to the transconductance amplifier with a nominal value of 2. The schematic is shown in Figure 19ucf28051 the board layout for the reference design is shown in Figure L determines the frequency range of the converter.

UCC from Texas Instruments

Additionally, pulling this pin below the ENABLE threshold turns off uccc28051 output switching, ensuring ucc28051 the gate drive is held off while the boost output is pre-charging, and also ensuring no runaway if the feedback path is open. Products conform ucc28051 specifications per the terms of Texas Instruments standard warranty.

The main switch selection is driven by the amount of ucc28051 dissipation allowable. Output ucc28051 the transconductance error amplifier.

Серия UCC (Texas Instruments)

This voltage is one of the inputs to the multiplier, with a dynamic input range of 2. The current sense resistor value must be chosen to limit the output power, and it must also use the full dynamic range of the multiplier ucc28051 normal steady state operation.

Input for the zero current detect comparator. Ucc20851 pin senses the instantaneous switch uxc28051 in the boost switch and uses it as the internal ramp for PWM comparator. The UCC is used for the off-line power factor corrected pre-regulator with ucc28051 over a universal input ucc28051 of 85 Ucc28051 to V ucc28051 a V DC regulated output.